12/1/2023 0 Comments Systemrescuecd xfsprogs![]() ![]() /dev/sda1, which will be used to hold the /boot filesystem,.Now, your GPT/GUID partitions have been created, and will show up as the following block devices under Linux: ![]() The partition table will now be written to the disk and gdisk will close. When you are satisfied with your partition setup, type " w" to write your configuration to disk: If you make a mistake, you can type " d" to delete an existing partition that you created. This option deletes all partitions and creates a new protective MBR.Īlong the way, you can type " p" and hit Enter to view your current partition table. Start gdisk:Ĭreate a new empty partition table (This will erase all data on the disk when saved): Adapt sizes as necessary, although these defaults will work for most users. The gdisk commands to create a GPT partition table are as follows. You can build legacy mode into your GPT partition table but it requires a BIOS Boot partition. I/O size (minimum/optimal): 512 bytes / 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes GPT data structures destroyed! You may now partition the disk using fdisk or Of course, you will need to change /dev/sdX to point to the block device of the USB stick on your system.įor steps on setting up network access from the LiveCD, please see the Funtoo:New Install Experience/LiveCD page. Root # dd if=funtoo-livecd-20220521-2138.iso of=/dev/sdX bs=4k status=progress oflag=sync Once downloaded, to copy it to a USB flash drive for booting, use the following command: This allows the Funtoo LiveCD to be used to even rescue and set up systems with different instruction sets! It also includes our innovative Fchroot tool, which allows you to use QEMU to "chroot" into non-x86 systems such as arm-64bit and riscv-64bit. In addition, our LiveCD is regularly updated, and includes NetworkManager which allows the use of the easy nmtui command to configure your network. Because it natively runs Funtoo Linux, and includes our official debian-sources kernel with very good hardware support, the hardware it supports is going to match the hardware that Funtoo Linux supports - thus allowing you to identify any hardware compatibility issues While any modern bootable Linux image should be sufficient to install Funtoo Linux, the Funtoo LiveCD has several advantages over other options. When installing Funtoo Linux on x86-64bit, we highly recommend the official Funtoo Linux LiveCD/LiveUSB, which can always be downloaded here: Now that we've covered all that important information, it's time to get started installing Funtoo Linux! See the page, Frankenchroot and Frankenchroot/Live_NFS_Frankenchroot for set-up information. This is a very effective tool for accelerating building of large pieces of software on resource-constrained ARM systems. New Fchroot Tool Our new fchroot tool is now available to allow you to run ARM and RISCV environments on PC-compatible hardware. Please see Chroot and Containers for an incomplete but growing list of container technologies available, along with links to further documentation. Containers LXD container management as well as Docker is officially supported. Running Steam We have recently released official Steam Docker Images as well as support for Steam on Flatpak - these are the officially-supported way to run Steam on Funtoo. Online users may find this more convenient. Documentation Styles We now offer the ability to read and browse the Install Guide section-by-section. Support Matrix Please use our Support Matrix to familiarize yourself with the technologies we do - and do not - support. We also have YouTube video tutorials to help you get started. See Development Guide for more information on how to contribute to Funtoo. If you use Funtoo Linux, you are welcome to contribute to its development via without going through any special procedure or complicated approval process. Development Model Funtoo Linux is a community-developed Linux meta-distribution. However, we recommend for all users to use next if possible and consider 1.4-release to be a legacy release unless you have very specific needs for something in 1.4-release. We also have 1.4-release available, which is a rolling release with an emphasis on long-term stability. This is actually a (mostly) rolling release with an emphasis on being current. ![]() Current Release The current release of Funtoo Linux is next, sometimes referred to as next-release.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |